WAN interface cards (WIC) modules

Module
Photo
Description
WIC-1AM

Cisco WIC-1AM module

The WIC-1AM provides one internal V.90 analog modems. This WIC can be used for basic telephone service connections. The WIC-1AM uses one port for connection to a standard telephone line, and the other port can be connected to a basic analog telephone for use when the modem is idle.

WIC-1ENET

Cisco WIC-1ENET module

The WIC-1ENET is a single-port 10 Mbps Ethernet interface card, for use with 10BASE-T Ethernet LANs.
WIC-1T

Cisco WIC-1T module

The WIC-1T provides a single port serial connection to remote sites or legacy serial network devices such as alarm systems, Synchronous Data Link Control (SDLC) concentrators, and packet over SONET devices.

Sync Max Speed : 2048 Mbit/s
Async Max Speed : 115.2 Kbit/s

WIC-2AM Cisco WIC-2AM module The WIC-2AM card features dual RJ-11 connectors, which are used for basic telephone service connections. The WIC-2AM has two internal V.90 analog modems to allow multiple data communication connections. These WICs can be used for incoming or outgoing analog modem calls.
WIC-2T

Cisco WIC-2T module

The 2-port asynchronous/synchronous serial network module provides flexible multi-protocol support, with each port individually configurable in synchronous or asynchronous mode, offering mixed media dial support in a single chassis. Applications for asynchronous/synchronous support include:

- Low speed WAN aggregation (up to 128 Kbps),
- Dial-up modem support,
- Async or Sync connections to management ports of other equipment,
- Transport of legacy protocols such as Bi-sync and SDLC.

HWIC-4ESW Cisco HWIC-4ESW module The HWIC-4ESW provides four switching ports.
HWIC-8A Cisco HWIC-8A module New module included in CiscoPacket Tracer 6.0.1Cisco ISR routers. This serial modules allows out of band management of Cisco networking devices through their console port. The HWIC-8A module allows the connection of 8 console cables using the octal cable, each serial connection being mapped to a TCP port for telnet access.
WIC-Cover

Cisco WIC cover

The WIC cover plate provides protection for the internal electronic components. It also helps maintain adequate cooling by normalizing airflow.

 

 

Network modules (NM)

Module
Photo
Description
NM-1E Cisco NM-1E module The NM-1E features a single Ethernet port that can connect a LAN backbone which can also support either six PRI connections to aggregate ISDN lines, or 24 synchronous/asynchronous ports.
NM-1E2W Cisco NM-1E2W module (2 WIC slots) The NM-1E2W provides a single Ethernet port with two WIC slots that can support a single Ethernet LAN, together with two serial/ISDN backhaul lines, and still allow multiple serial or ISDN in the same chassis.
NM-1FE-FX

Cisco NM-1FE-FX module

The NM-1FE-FX Module provides one Fast-Ethernet interface for use with fiber media. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards. Single port network modules offer autosensing 10/100BaseTX or 100BaseFX Ethernet.
NM-1FE-TX

Cisco NM-1FE-TX module

The NM-1FE-TX Module provides one Fast-Ethernet interface for use with copper media. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards. Single port network modules offer autosensing 10/100BaseTX or 100BaseFX Ethernet. The TX (copper) version supports virtual LAN (VLAN) deployment.
NM-1FE2W Cisco NM-1FE2W module (2 WIC slots) The NM-1FE2W Module provides one Fast-Ethernet interface for use with copper media, in addition to two Wan Interface Card expansion slots. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards. Single port network modules offer autosensing 10/100BaseTX or 100BaseFX Ethernet. The TX (copper) version supports virtual LAN (VLAN) deployment.
NM-2E2W   The NM-2E2W provides two Ethernet ports with two WIC slots that can support two Ethernet LANs, together with two serial/ISDN backhaul lines, and still allow multiple serial or ISDN in the same chassis.
NM-2FE2W   The NM-2FE2W Module provides two Fast-Ethernet interfaces for use with copper media, in addition to two Wan Interface Card expansion slots. Ideal for a wide range of LAN applications, the Fast Ethernet network modules support many internetworking features and standards.

NM-2W

  The NM-2W Module provides two WAN Interface Card expansion slots. It can be used with a broad range of interface cards, supporting a diverse array of physical media and network protocols.
NM-4A/S Cisco NM-4AS module The 4-port asynchronous/synchronous serial network module provides flexible multi-protocol support, with each port individually configurable in synchronous or asynchronous mode, offering mixed-media dial support in a single chassis. Applications for Asynchronous/Synchronous support include: Low speed WAN aggregation (up to 128 Kbps), dial-up modem support, Async or Sync connections to management ports of other equipment, and transport of legacy protocols such as Bi-sync and SDLC.
NM-4E   The NM-4E features four Ethernet ports for multifunction solutions that require higher-density Ethernet than the mixed-media network modules.
NM-8A/S   The 8-port asynchronous/synchronous serial network module provides flexible multi-protocol support, with each port individually configurable in synchronous or asynchronous mode, offering mixed-media dial support in a single chassis. Applications for Asynchronous/Synchronous support include: Low speed WAN aggregation (up to 128 Kbps), dial-up modem support, Async or Sync connections to management ports of other equipment, and transport of legacy protocols such as Bi-sync and SDLC.
NM-8AM Cisco NM-8AM module The NM-8AM Integrated V.92 analog modem network module provides cost-effective analog telephone service connectivity for lower-density remote-access service (RAS), dial-out and fax-out modem access, asynchronous dial-on-demand routing (DDR) plus dial backup, and remote router management. Both the 8-port and 16-port versions use RJ-11 jacks to connect the integrated modems to basic analog telephone lines on the public switched telephone network (PSTN) or private telephony systems.
NM-Cover   The NM cover plate provides protection for the internal electronic components. It also helps maintain adequate cooling by normalizing airflow.

 

Optical transceivers

Module
Photo
Description
GLC-GE-100FX The 100BASE-FX SFP module for Gigabit Ethernet ports, 1310 nm wavelength, 2 km over MMF.
GLC-LH-SMD Cisco GLC-LH-SMD 1000BASE-LX/LH SFP is made for Both Multimode and Single-Mode Fibers.The 1000BASE-LX/LH SFP, compatible with the IEEE 802.3z 1000BASE-LX standard, operates on standard single-mode fiber-optic link spans of up to 10 km and up to 550 m on any multimode fibers. When used over legacy multimode fiber type, the transmitter should be coupled through a mode conditioning patch cable.